Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

ALUKID

Anti-corrosion aluminium primer-enamel
For interior use
For exterior use
The product can be applied by roller
The product can be applied by brush
The product can be applied with spray gun
Use appropriate solvent for diluting and tools cleaning
Drying time 12 h
Packaging 0.45 l, 0.9 l, 20 l
Consumption 8 - 10 m²/l
Nearest store
Consumption calculator
Description
Usage

ALUKID is an alkyd polymer based aluminium primer-enamel. Intended for protection of metal surfaces against corrosion outdoors and indoors.

May be applied directly on steel surfaces or on surfaces previously primed with GF-021, RIATOP PRIMER, NOVAKOR, NEOSPRINT PRIMER, VL-02 primers. Stir ALUKID thoroughly before use. If necessary, dilute to working viscosity with white spirit or VAITSOL solvent: 0 to 5% by volume; apply with a roller or paint brush. Use the same solvents also to clean work tools.  Application of ALUKID by spraying is allowed only in designated painting facilities of industrial plants and workshops. Before applying ALUKID, dirt and corrosion products (rust) should be removed from the surface to be painted. In cases where complete cleaning of the surface from corrosion products is not possible, it is necessary to clean at least the loose rust layer and perform the maximum possible surface treatment with abrasive tools such as sandpaper, steel brush, power grinders, etc. In this case, a possible reduction in the anti-corrosion effectiveness should be taken into account. Apply to prepared surfaces with a spray gun, paint brush or roller in 1 to 2 coats if the surface has been primed beforehand, or in 2 to 3 coats when painting non-primed surfaces. Air temperature must not be lower than +5 °C, relative air humidity – not higher than 85%. Primer-enamel consumption: 8 to 10 m2/l for one coat. Drying time at 20 ± 2 °C: not more than 12 hours.

Need help?
info@rilak.lt
+371 67 458 776
Question about the product
Description

ALUKID is an alkyd polymer based aluminium primer-enamel. Intended for protection of metal surfaces against corrosion outdoors and indoors.

Usage

May be applied directly on steel surfaces or on surfaces previously primed with GF-021, RIATOP PRIMER, NOVAKOR, NEOSPRINT PRIMER, VL-02 primers. Stir ALUKID thoroughly before use. If necessary, dilute to working viscosity with white spirit or VAITSOL solvent: 0 to 5% by volume; apply with a roller or paint brush. Use the same solvents also to clean work tools.  Application of ALUKID by spraying is allowed only in designated painting facilities of industrial plants and workshops. Before applying ALUKID, dirt and corrosion products (rust) should be removed from the surface to be painted. In cases where complete cleaning of the surface from corrosion products is not possible, it is necessary to clean at least the loose rust layer and perform the maximum possible surface treatment with abrasive tools such as sandpaper, steel brush, power grinders, etc. In this case, a possible reduction in the anti-corrosion effectiveness should be taken into account. Apply to prepared surfaces with a spray gun, paint brush or roller in 1 to 2 coats if the surface has been primed beforehand, or in 2 to 3 coats when painting non-primed surfaces. Air temperature must not be lower than +5 °C, relative air humidity – not higher than 85%. Primer-enamel consumption: 8 to 10 m2/l for one coat. Drying time at 20 ± 2 °C: not more than 12 hours.

Question about the product
Patēriņa kalkulators

Contact us

We will be happy to help

Consumption calculator

Find out how much of the product You will need.

Produkts:
Consumption
ALUKID
8 m²/l
Surface area
Based on our calculations You will need approximately:
0
liters of product for one coating

SIA Rīgas laku un krāsu rūpnīca

Daugavgrīvas iela 63/65, Rīga, LV-1007

Reģistrācijas Nr.: 40003284444

PVN Nr.: LV40003284444

Banka: A/S Swedbank

Konts: LV23HABA0019308047593

Bankas kods: HABALV22

Contact us

We will be happy to help